Артикул: HE2114012
Бренд: Heltun
Кол-во: Tellimisel
129,99 €


* цвет

Кол-во: - +
   - или -   
HELTUN 5 kanaliga puutetundliku lüliti asendab olemasoleva seinalüliti ning võimaldab manuaalset - või kaugelt (sisse / välja) juhtimist


The HELTUN 5 channels wall touch panel switch replaces an existing in-wall switch and enables manual or remote switch (On/Off) controls of lights, blinds, motors and heating systems with a maximum load of 5A for each channel.

Powerful, efficient and well-designed, HELTUN is the thinnest and most stylish switcher on the market. Featuring a crystal-clear glass window, its fire and short circuit resistant recycled-plastic casing is only 9mm thick.

Internal sensors
HELTUN switchers also feature built-in temperature, humidity and light sensors.

Inputs & outputs
The main power input is 100-250VAC. The switcher has 5 relay outputs each with max 5A load. It also has two independent inputs for relay channels which allow it to control systems with different power sources or to use outputs as dry contacts. E.g. to switch On/Off 220VAC light and control motorized valve with 24VDC power.

Input 1 with the required power source is for relay channels 1, 2 and 3, which can be loaded up to a max 15A.

Input 2 with the required power source is for relay channels 4 and 5, which can be loaded up to a max 10A.

Know how much energy you are using
With the HELTUN built-in power consumption logic you can monitor precisely how much energy was used during any particular day, week or month for each channel. Just specify the consumption of the load in watts for each relay channel and the special logic will calculate total consumption relatively to the time since the output is in the ON state.

Customize Functions
1) Each touch button can be configured to control any relay output. Up to five relay output can be controlled by each button.

2) 4 different modes for each relay control: switch only On, switch only Off, invert, hold (switch to On when button is pressed and switch to Off when button is released)

3) Relay outputs can be controlled by timer: press the button the relay will be switched ON and after specified time automatically switched OFF. This function can be used to open/close garage doors, blinds, curtains, etc.

4) Each button, backlight and relays output are completely independent. They are managed by the main controller or associated device. In this state buttons can be used to run scenarios and the backlight can indicate the Mode or device status.

The panel has 5 touch buttons which are super sensitive and react even before physical touch, in fact processing at 1-2mm distance. Each button has a two colour (red and blue) back light.

4 different brightness levels of each colour back light can be controlled manually by setting the value in the parameters or in automatic mode. Automatic brightness control seamlessly adjusts the buttons backlight level to the ambient light conditions making it easy to use even in the dark.

Easy to install
HELTUN devices can be easily installed into any standard wall fitment (rectangular or round). No special skills are required for installation.

Z-Wave Plus S2 Certified
Connect your HELTUN devices to the Smart Home controlling system using the latest secure Z-Wave plus chip with new advanced Security 2 (S2) framework (AES 256 encryption method for data transfer).

The HELTUN switcher is compatible with all Z-WAVE certified controllers and devices.

With the Z-Wave controller, you can manage all the functions of the switcher via a mobile application, including simulation of each button press, viewing accurate energy consumption charts and much more.

Also, up to 10 separate devices can be connected to the Switcher. You can associate with the Heltun Switcher any Z-Wave compatible relay and control door locks, valves, blinds, curtains and other motorized systems.



  • Inclusion/exclusion into/from z-wave network
  • Association control of 10 devices from network
  • Customize functions of touch buttons
    • Switch the relay On only
    • Switch the relay Off only
    • Invert the state of the relay
    • Hold function (Momentary switch)
  • Choosing the relay channel for each button control
  • Up to 5 different relays channel can be control by one button
  • Relay outputs control by timer
  • Exclusion of any relay from control
  • Setup each button to control device from association group
  • Back light colors invert
  • Software energy consumption meter for each channel
  • Temperature sensors calibration
  • Adjustable LCD brightness: Auto or Manual
  • Consumption meter reset
  • Factory reset
  • OTA function (Firmware update over the air).


  • Front frame dimensions: 89x89x9mm
  • Back dimensions: 53x53x28mm
  • Material: Flame retardant plastic, tempered glass
  • Frame colors: White
  • Glass colors: White
  • 5 sensitive capacitive touch buttons
  • Red and Blue color LED back light for each button
  • 4 levels adjustable brightness for back light
  • 5 channel relay output, resistive load up to 5A each
  • 2 independent inputs for relays channel
  • Operating temperature: -10°C – +60°C
  • Power supply: 100V – 230VAC, 50Hz/60Hz
  • Power consumption: 2.0W
  • Max resistive load: 5A for each output channel
  • Relays life time: 100.000 switches
  • Internal ambient brightness sensor
  • Internal temperature sensor
    • Measurement range: -40°C to +125°C
    • Accuracy: ±0.5°C
  • Internal humidity sensor
    • Measurement range: 0 – 80%RH
    • Accuracy: ±3.0%RH
  • Energy consumption meter
  • IP class: IP21
  • Z-Wave frequency: EU-868/869 MHz (other frequencies available on request)
  • Z-Wave SDK: V6.71
  • Z-Wave Plus module: ZM5202
Схожие продукты
FIBARO Relay Switch предназначен для установки в стандартных настенных распределительных коробках или в каких-либо других местах, где необходимо управлять электрическими приборами. Как и в случае со всеми другими устройствами, FIBARO Relay Switch может управлять подключенными устройствами либо через Z-Wave сеть, либо с помощью непосредственно подключенного к нему выключателя.
Артикул: FGS-212 ,   Кол-во: 12
59,99 €
Tooteinfo "MCO Home Klaasist puutetundlik lüliti GEN5 (1 nupp)"
MCO Home'i TPS411 GEN 5 on integreeritud lülitusrelee ja stseeniregulaatoriga seinalüliti. Releed saab kontrollida nii klaaspinna kui ka Z-Wave'i käskude abil ühendatud puutelülitiga. Releel saab vahetada koormust kuni 1100 vatti. Kohaliku lülitamise kõrval saab seadet ka jagada kahte rühme, mis on otseselt seotud seadmega. Iga nupu sinine LED tähistab lülitusolekut.

Seina lüliteid saab hõlpsasti ühendada elektrilise koormaga, ilma et oleks vaja eraldi paigaldada lukustatavat moodulit. Relee asub mooduli sees, mis on vahetult ühendatud klaasist puutetundliku nupuga. Selle MCO Home seadme lülitiga saate asendada mis tahes lüliti. Seina lüliti saab paigaldada mistahes kaablikarbikule.

MCO Home stiilne klaasist seina lülitiga saate juba paigaldatud tuled hõlpsasti integreerida oma koduautomaatika võrku. Uusi kaableid paigaldamata võite oma valgustuse lülitada seinalüliti kaudu tavapäraselt - aga tänu Z-Wave'i tehnoloogiale ka kaugjuhtimispuldi, nutitelefoni või sensoriga juhitava automaatika abil.
Uue funktsiooni abil saate nüüd oma seadistatud stseene käivitada ainult ühe puudutusega.
Артикул: MH-S411 ,   Кол-во: Tellimisel
89,91 €
Артикул: FG-WDSEU221-AS-8001 ,   Кол-во: Tellimisel
59,00 €
Артикул: FG-WREU111-AS-8001 ,   Кол-во: Tellimisel
59,00 €
Артикул: FG-Wx-AS-4001-10 ,   Кол-во: Tellimisel
44,55 €